10 Best
Cpu Fan Controllers
-
Product Highlights- Cooling when you need it - quiet when you don't. the red port on our pwm fan controller allows the operating system to adjust fan speed based on temps. the pwm fan hub then matches the power level for the other ports
- No frills, all function - strong wire connections and clean sleeving are part of our simple, cost effective design. take care during installation to avoid bending the pins and capacitor
- Manages multiple fans - if your motherboard lacks fan interfaces, our pwm fan hub is the neat and tidy way to expand. the 12v fan controller accurately controls 4-pin fan speed from a single case input
- Easy installation - just plug the molex fan controller into the motherboard and connect to the psu. double-sided adhesive mounts the pc fan hub to any flat surface and the screw hole allows it to be fixed to the chassis
- Backed by a manufacturer's warranty, if your fan hub falls short of your expectations for any reason, contact us for a full refund
SHOWview product -
Product Highlights
- 【function】the hub has a motherboard rgb synchronization function (for light bars), pwm function and fan power. support synchronous mainboard control and remote control of lighting effects. 1 to 8 fan multi‑port for sata hub power supply 12v 4‑pin pwm argb addressable distributor for pc led light cooler control adapter.
- 【easy to use】two interfaces on the left, the one on the left is the light 5v argb motherboard synchronous interface, if you want to use the synchronous direct connection, press the mb key on the remote control for 6 seconds to adjust the synchronization; the one on the right is the fan running at full speed when the motherboard temperature control interface is not conne...
- 【rgb splitter hub】the two‑in‑one controller is equipped with a remote control, a mainboard synchronization cable, and a control cable temperature. if the motherboard does not support synchronization, you can use the remote control and do not need to connect the synchronization cable. direct output with power interface, more expressive and efficient.
- 【professional】8 argb (5v 3pin), 8 fan (4pin) pwm function, 1x3 pin lighting 5v argb motherboard synchronization, 1 motherboard temperature control port, for sata power supply, and the remote control button is 21 keys.
- 【note】four temperature control center line on the left and right sides, the red temperature control interface must be connected to the temperature control fan, the light interface can be freely connected, the for sata interface on the right must be connected.
SHOWview product -
Product Highlights
- Pwm function: each port has its own pwm function and the fan speed can be adjusted at the same time. (only the speed of the red port can be identified by the system.)
- Easy to install: double-sided adhesive for easy installation and more stable standing in the surface.
- 10-port fan hub: supports 10 pwm 4 pin fans at the same time. compact design can save space and make the wire more tidy.
- Stable sata power input: simple and stable. only one sata connection to the system.
SHOWview product -
Product Highlights
- Whether it is a 2-wire, 3-wire or 4-wire fan (only connect power cable), whether pwm or brushless fans, as long as the fan voltage is within 12v, current less than 1a, the governor apply! also can drive a of fans (total current must<1a). 【3-wire/4-wire fans only need to connect the fan's power cord to the controller】
- Dual working mode optional, fixed starting temperature or adjustable starting temperature. fixed mode temperature and temperature of 30°c(86°f), the governor control fan start, 30 to 50 degrees fan speed linear increase, 50°c(122°f ) above the fan at full speed. adjustable mode start-up temperature range: 15 to 50 degrees, full speed range of 35 to 70 degrees (start and...
- This dc12v governor can be controlled according to the ambient temperature of the fan speed, no manual control, automatic stepless speed, the higher the ambient temperature, the faster the fan speed control, saving energy and reducing noise.
- The temperature sensor is connected with a cable in the form of mounting holes to facilitate detection of the temperature specified temperature point. temperature probe is sealed with epoxy resin, waterproof and moisture-proof, the temperature probe maximum use temperature of 110 degrees. sensor probe length: 300mm/11.5inch.
- Board size: 1.77x1.0x1.18inch/ 45x25x30mm (lxwxh), m3 mounting hole. ( note that it is best to read the main picture instructions before use)
SHOWview product -
Product Highlights
- If the speed of the fan changes and the direction of adjustment is opposite, it means that the fan is a reverse-sequence fan, and the (pf) setting point needs to be short-circuited with solder, and the power must be turned off before operation to avoid damage! the short-circuited pwm signal changes in the reverse direction with the adjustment, and the reverse-sequence f...
- Fan current 3a this current is limited by switches and connectors, and the capacity can be expanded by taking the power line separately. for fans over 3a, connect a large current fan method: the positive and negative poles of the power supply of the fan can be connected to the power supply, the positive and negative poles of the fan are connected to the power supply sep...
- This is a four-wire pwm fan speed controller. it can only control 12v four-wire fans that support pwm speed regulation. for example, many 12v four-wire chassis or cpu fans cannot control 2-3-wire fans.
- Pay attention to the positive and negative poles and the power supply voltage. after the power supply fan is connected, it can be used. the potentiometer is turned off counterclockwise to the end, and the clockwise end is the maximum output. a separate small adjustable resistor (starting speed adjustment) on the board is used to adjust the speed of the just-open position.
- Consumption less than 20ma without fan pwm signal model 0-5v 25khz pwm signal output range 0% to 100% start of pwm adjust range 0% to 60% output interface 2510-4p, 2.54mm space size 26*20mm, knob screw extension 15mm installation opening 7mm
SHOWview product -
Product Highlights
- Multiple fans can be used in parallel (total current does not exceed 5a), support automatic temperature control and air cooling speed control, temperature control speed has four temperature zone settings, widely used.
- Circuit load capacity: 5a for each output and 8a for bus current.
- Supports all internal 12v 5a fans, synchronous rectified output, high efficiency, no need for additional heat sinks even for high current operation.
- It can be turned on with the three-wire fan monitoring function (stall warning).
- Output range: 20%-100% for the first channel, or 40%-100% for the first channel (tfl = on), 10%-100% for the second channel and the third channel. (note: the above range is only applicable to the pwm range, the actual control effect will vary depending on the fan)
SHOWview product -
Product Highlights
- Synchronous fan control: your set pwm signal is passed on synchronously to all fans connected to the case fan hub, the rpm of the first fan slot are read out and returned to your system
- External power supply: the fans are powered directly from your power supply via sata power, there is no voltage loss at the fan speed and smooth, smooth operation is made possible
- Cable management: case fan hub can be placed in housing, it's connected to motherboard with one cable, you can do without many additional cables and lay them freely in the invisible part of housing
- Expand your ventilation: even if you don't have enough fan headers on your mainboard, the case fan hub expands your system by 9 more case fan slots
- Technical details: output: 10 x 4-pin pwm socket, output current: up to 1 a per port, input: sata power + 4-pin fan header, input current: up to 4.5 a, dimensions: 55.6 x 86.3 x 14.3 mm, weight: 50 g
SHOWview product -
Product Highlights
- Circuit load capacity: maximum current per output 5a, the bus currents up 9a
- Bf1 bf2 (no. 4,5): corresponds fan1 fan2 stall alarm function switch, when the corresponding open channel fan break down, the controller will alarm with soundand light (works with buzzle), alarm will automatically eliminated when the fan is rotated recovery . if bf1 and bf2 both are open (on), the fan1, fan2 have any one or both stops, the controller will alarm!
- Support all within 12v 5a fans, synchronous rectifier output, high efficiency! even if a large current work does not require additional heat sink! a plurality of fans can be used in parallel (total current does not exceed 5a), supports automatic temperature control and manumotive speed control, temperature control speed with four temperature zones for setting up, easy t...
- When the temperature lower than the accelerated temperature, then output at the minimum rotation speed; when it exceed over the full temperature, then always output at full speed.
SHOWview product -
Product Highlights
- Function: pc 8 channel fan hub reduces speed when computer components are idle to reduce noise and power consumption. when the computer part is busy, increase the speed to reduce the computer part temperature.
- Widely used: widely used in pc computer water cooling system, the fan interface is 4pin (3pin can be connected). the power interface is a interface.
- Knob adjustment: 1 manual adjustment knob, high accuracy, good performance, equipped with an independent speed controller, the speed can be adjusted at will.
- High quality materials: made of high quality plastic and metal materials, it is durable, reliable, low loss and low heat.
- Space saving: the pc 8 channel fan hub is installed in the pci position of the chassis, which is easy to install and does not take up space.
SHOWview product -
Product Highlights
- In the hub interfaces, the red cpu interface is the cpu fan dedicated interface (with speed detection function). since the mainboard can only receive one rotation speed signal, the remaining nine conventional fan interfaces have the pwm function, but no speed signal.
- There is eva double-sided adhesive at the back of the hub, which can be easily affixed to a flat place. also a fixing screw hole in the middle of the pcb to facilitate fixing to a part of the chassis.
- Expand 4-pin fan interfaces, solving the problem of lack of motherboard fan interfaces. designed for 12v 4-pin 3-pin fans, support simultaneous starting at most 10 channel fans.
- For both 4-pin and 3-pin fans. please note 4pin fan speed can be adjusted by temperature control. 3pin fan can also be used, but because 3pin has no pwm function, it is at fixed speed after inserting.
- Red is expected to be a pass through for the cpu fan. so, the hub has a power source fed from the computer power supply, then the speed is regulated by the speed for the "source" fan. you can connect to the cpu fan lead on the system board or the chassis fan lead. the ten fans will spin at the same speed, that designated by the system for that fan. if the chassis fan is...
SHOWview product
Coupon copied
